Analog Devices ADSP-BF535 Blackfin Hardware Reference Manual Download | Manualshive

Page: 727 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

18-3

External Bus Interface Unit

The next region is reserved memory space. References to this region do
not generate external bus transactions. Writes have no effect on external
memory values, and reads return undefined values. The EBIU generates
an error response on the internal bus, which will generate a hardware
exception for a core access or will optionally generate an interrupt from
PCI or a DMA channel, depending on where the access originated.

The PCI space shown at the top of the external memory map is supported
by the PCI Controller, not the EBIU. For more information, refer to
Chapter 15, “PCI.”

Block Diagram

Figure 18-2

is a conceptual block diagram of the EBIU and its interfaces.

Since only one ADSP-BF535 processor can be accessed at a time, control,
address, and data pins for each memory type are multiplexed together at
the pins of the device. The Asynchronous Memory Controller (AMC) and
the SDRAM Controller (SDC) effectively arbitrate for the shared pin
resources.

«
...
725
726
727
728
729
...
»

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

Brand: XMG Pages: 5

Brand: NAD Pages: 2

Brand: PaloAlto Networks Pages: 3

Brand: Direct IP Pages: 76

Brand: A2B Electronics Pages: 24

Brand: ZALMAN Pages: 6

Brand: ETAS Pages: 82

ExpressBox2 EB2

Brand: Magma Pages: 74

Brand: ICP DAS USA Pages: 8

Brand: Penguin Edge Pages: 2

Brand: National Instruments Pages: 80

Brand: Advantech Pages: 108

Brand: Konica Minolta Pages: 31

Brand: Idis Pages: 18

Brand: TANDBERG Pages: 2

Brand: IBM Pages: 168

Cypress CapSense P0080

Brand: Terasic Pages: 22

Brand: Lanner Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands