manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

Device Mode Operation

13-10

ADSP-BF535 Blackfin Processor Hardware Reference

 

Inbound Transactions (ADSP-BF535 Processor as 

PCI Target)

This section describes inbound transactions with the ADSP-BF535 pro-
cessor as the PCI target.

General Inbound Operation

To participate on a PCI bus as a target, the ADSP-BF535 processor must 
first be configured. First, the processor core must write to the Memory 
and I/O BAR Mask registers. Every bit set by the core in each of these 
masks allows the corresponding bit in the memory base address register 
(BAR) or I/O BAR, respectively, to be written by the PCI host during 
configuration. The number of upper bits writable by the PCI determines 
the size in bits of the base address register that configuration software on 
the PCI side programs into the BAR. This determines the size of the win-
dow for which the PCI interface can claim the transaction as the intended 
target.

Each bit of the mask registers must be set to 1 by the processor core, start-
ing with the uppermost bit (bit 31). To prevent the core from claiming 
either memory or I/O transactions, the corresponding mask should be 
programmed with all 0s (the default state). The pattern of all 1s is 
assumed by the PCI interface to be contiguous, stray 0s make the bit non-
writable, and cause unpredictable results.

The processor core must also program the 

PCI_TMBAP

 and 

PCI_TIBAP 

regis-

ters. These registers are the base address pointers (BAPs) for incoming 
memory and I/O transactions, respectively. The number of bits pro-
grammed into the upper portion of each of these registers must be the 
same as the number of bits set in the corresponding mask. Any bits written 
in the space where 0s exist in the mask are ignored, but the write to the 
BAP completes successfully. If memory or I/O transactions are not 
needed, then the corresponding BAP register is ignored and does not need 
to be programmed. When the processor core has completed writing to 

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

ADC PG-FlexPlus AMU-912 Manual preview
PG-FlexPlus AMU-912
Brand: ADC Pages: 130
Fieldbus Specialists AT-FBUS Getting Started preview
AT-FBUS
Brand: Fieldbus Specialists Pages: 39
ETC Power Control Processor Configuration Manual preview
Power Control Processor
Brand: ETC Pages: 64
Intel Core 2 Quad Q9400 Product Brief preview
Core 2 Quad Q9400
Brand: Intel Pages: 2
Lanner electronics EM-566 Series Manual preview
EM-566 Series
Brand: Lanner electronics Pages: 59
NEC Thin Client US310e Getting Started preview
Thin Client US310e
Brand: NEC Pages: 6
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Brand: Sans Digital Pages: 9
Crystal Vision TANDEM HD-21 User Manual preview
TANDEM HD-21
Brand: Crystal Vision Pages: 54
Advantech PCM-4141 Series User Manual preview
PCM-4141 Series
Brand: Advantech Pages: 96
Uniflair PCOWeb Instruction Manual preview
PCOWeb
Brand: Uniflair Pages: 24
National Instruments SC-2040 User Manual preview
SC-2040
Brand: National Instruments Pages: 56
Cypress Semiconductor CY7C027AV Specification Sheet preview
CY7C027AV
Brand: Cypress Semiconductor Pages: 18
ZALMAN CNPS9500 AT User Manual preview
CNPS9500 AT
Brand: ZALMAN Pages: 9
WiebeTech FCDKV4 User Manual preview
FCDKV4
Brand: WiebeTech Pages: 8
DOD 410 SERIES II Owner'S Manual preview
410 SERIES II
Brand: DOD Pages: 12
Silex technology Embedded Intelligent Module SX-560 Developer'S Reference Manual preview
Embedded Intelligent Module SX-560
Brand: Silex technology Pages: 110
ADLINK Technology ROScube-I Series User Manual preview
ROScube-I Series
Brand: ADLINK Technology Pages: 95
ekwb EK-FC670 GTX Series Installation And Mounting Manual preview
EK-FC670 GTX Series
Brand: ekwb Pages: 2

Brands by name

Popular brands

Load more brands