Analog Devices ADSP-BF535 Blackfin Hardware Reference Manual Download | Manualshive

Page: 138 / 1022

background image

Reset State

3-10

ADSP-BF535 Blackfin Processor Hardware Reference

Idle state can be entered only in Supervisor mode, and the processor
returns to Supervisor mode when transitioning from the Idle state. Appli-
cation programs in User mode cannot invoke the Idle state, except
through a system call provided by an operating system kernel.

In the following code example, core interrupts are disabled and the

IDLE

instruction is executed. When all the pending processes have completed,
the core disables its clocks. Idle state can be terminated only by asserting a

WAKEUP

signal. For more information, see

“System Interrupt

Wakeup-Enable Register (SIC_IWR)” on page 4-24

. While not required,

an interrupt could also be enabled in conjunction with the

WAKEUP

signal.

When the

WAKEUP

signal is asserted, the processor finishes executing the

SSYNC

instruction. The next instruction in this sequence should be the

STI

. Interrupts are enabled after this instruction is executed.

Example Code for Transition to Idle State

To transition to the Idle state, use code as shown in

Listing 3-3

.

Listing 3-3. Transitioning to Idle State

CLI R0 ; /* disable interrupts */

IDLE ; /* source NOPs into pipeline and assert IDLE output on

SSYNC */

SSYNC ; /* drain the pipeline, IDLE asserts after SSYNC_ACK

back from system */

STI R0 ; /* re-enable interrupts after wakeup */

Reset State

Reset state initializes the processor logic. During Reset state, application
programs and the operating system do not execute.

«
...
136
137
138
139
140
...
»

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

Brand: Xinje Pages: 57

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

SRCSASBB8I - RAID Controller

Brand: Intel Pages: 36

Scorpio WD2500BPVT

Brand: Western Digital Pages: 3

Scorpio WD2500BPVT

Brand: Western Digital Pages: 4

Procont LMC-008-IO

Brand: janitza Pages: 28

Brand: Z Microsystems Pages: 51

Brand: WABCO Pages: 29

Brand: Kramer Pages: 2

Smartio CP-104UL

Brand: Moxa Technologies Pages: 2

Brand: HYCON Pages: 13

Brand: Omnia Pages: 130

System 200V PC 288

Brand: VIPA Pages: 54

Brand: AMD Pages: 10

Application Module 9109 OCU-DP

Brand: Paradyne Pages: 8

AN5506-04 Series

Brand: FiberHome Pages: 146

Brand: Extron electronics Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands