Analog Devices ADSP-BF535 Blackfin Hardware Reference Manual Download | Manualshive

Page: 63 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

1-9

Introduction

In addition, the PCI interface can either be used as a bridge from the pro-
cessor core as the controlling CPU in the system or as a host port where
another CPU in the system is the host and the ADSP-BF535 processor is
functioning as an intelligent I/O device on the PCI bus.

When the ADSP-BF535 processor acts as the system controller, it views
the PCI address spaces through its mapped windows. It can initialize all
devices in the system and maintain a map of the topology of the
environment.

The PCI memory region is a 4 Gbyte space that appears on the PCI bus
and can be used to map memory on I/O devices on the bus. The
ADSP-BF535 processor uses a 128 Mbyte window in memory space to see
a portion of the PCI memory space. A base address register positions this
window anywhere in the 4 Gbyte PCI memory space while its position
with respect to the processor addresses remains fixed.

The PCI I/O region is also a 4 Gbyte space; however, most systems and
I/O devices use only a 64 Kbyte subset of this space for I/O mapped
addresses. The ADSP-BF535 processor implements a 64 Kbyte window in
this space, along with a base address register that positions the window
anywhere in PCI I/O address space, while the window remains at the same
address in the processor address space.

PCI configuration space is a limited address space that is used for system
enumeration and initialization. It is a very low performance communica-
tion mode between the processor and PCI devices. The ADSP-BF535
processor provides a 1-value window to access a single data value at any
address in PCI configuration space. This window is fixed and receives the
address of the value, and the value if the operation is a write. Otherwise
the device returns the value into the same address on a read operation.

«
...
61
62
63
64
65
...
»

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: National Instruments Pages: 9

FIELDPOINT FP-1600

Brand: National Instruments Pages: 8

Brand: Dahua Pages: 24

Brand: DAQ system Pages: 41

Brand: DAQ system Pages: 19

CLICK PLUS C2-02CPU

Brand: Automationdirect.com Pages: 10

PISO-725 Series

Brand: ICP DAS USA Pages: 8

Brand: ETAS Pages: 82

Brand: Kramer Pages: 2

Brand: Netopia Pages: 138

Brand: Goobay Pages: 28

Brand: MACHINIST Pages: 15

Brand: peplink Pages: 111

Liebert ISWEBRT3

Brand: Emerson Pages: 28

PACSystems IC695CPE400

Brand: Emerson Pages: 37

Dixell iChill ICX207D

Brand: Emerson Pages: 20

Fisher FIELDVUE DLC3020f

Brand: Emerson Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands