Analog Devices ADSP-BF535 Blackfin Hardware Reference Manual Download | Manualshive

Page: 612 / 1022

background image

Requirements

14-4

ADSP-BF535 Blackfin Processor Hardware Reference

Data Flow and Traffic Scheduling

Data flows between the USB host and the attached devices in units of
packets, which are normally 8, 16, 32 or 64 bytes. An exception is the iso-
chronous data type, where packets can be as large as 1023 bytes. The
packets are grouped into larger units called transfers.

To allocate the serial bus bandwidth fairly across all of the attached USB
devices and endpoints, the USB host implements a traffic scheduling algo-
rithm. From the point of view of a USB device, this algorithm is not
deterministic. Although the specific scheduling algorithm is standardized,
the bus dynamically reallocates bandwidth based on factors such as packet
error conditions and flow control. So far as the device is concerned, it can
receive transfer requests for any endpoint at any time.

Depending on the bus loading, the USB host may request packets
back-to-back, or it may request packet transfers to each endpoint in a
round-robin fashion. The USB protocol also allows for detection and
retransmission of packets in cases of bit errors and flow control problems.

Each USB device implementation must maintain state information for
each endpoint that allows large data transfers to occur a packet at a time.
Each device must also maintain state information for each packet to be
retransmitted.

USB Implementation

The ADSP-BF535 processor’s USBD implementation includes:

• The peripheral has a single interrupt output (

USBD_INTR

).

• System software is responsible for managing interrupt priority and

requeueing low priority events as software interrupts.

• Memory access for the USB endpoints is by means of the DAB as a

bus master.

«
...
610
611
612
613
614
...
»

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

Brand: EAW Pages: 2

Brand: ICP DAS USA Pages: 8

Brand: Intel Pages: 108

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: Cypress Semiconductor Pages: 16

Brand: M86 Security Pages: 309

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

CY62136EV30 MoBL

Brand: Cypress Semiconductor Pages: 12

Brand: Airlink101 Pages: 46

Brand: AMD Pages: 45

Brand: Avigilon Pages: 12

FiberTwist XGS2410

Brand: Genexis Pages: 7

Brand: Cutting Edge Pages: 92

Wisenet XRN-6410DB4

Brand: Hanwha Techwin Pages: 118

Brand: silicom Pages: 16

Cascade Express

Brand: Riverbed Pages: 92

Brand: Transition Networks Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands