manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

ADSP-BF535 Blackfin Processor Hardware Reference

9-25 

 

Direct Memory Access

Peripheral DMA Descriptor Ready Register

If a descriptor block’s DBO bit is 0 when the descriptor block Configura-
tion Word is accessed, the DMA channel halts. Writing a 1 to bit 0 of the 
peripheral’s DMA Descriptor Ready register synchronizes the DMA chan-
nel, causing the Configuration Word to be reloaded into the DMA 
Configuration Register and causing bit 15 to be rechecked. If this bit is 
set, processing of the descriptor block resumes. Bit 0 of the peripheral’s 
DMA Descriptor Ready register remains set until a descriptor block has 
been successfully fetched. After a successful fetch, bit 0 of the DMA 
Descriptor Ready register is cleared. 

Figure 9-10

 describes the peripheral 

DMA Descriptor Ready register.

This register is not used for autobuffer mode. 

Figure 9-9. DMA Descriptor Base Pointer Register

Figure 9-10. Peripheral DMA Descriptor Ready Register

DMA Descriptor Base Pointer Register (DMA_DBP)

15 14

13 12

11 10

9

8

7

6

5

4

3

2

1

0

1

Address[31:16] of 
Descriptor Block 
Base Pointer

1

1

1

1

0

0

0

0

0

0

0

0

0

0

1

Reset = 0xF003

0xFFC0 4880

15 14

13 12 11 10

9

8

7

6

5

4

3

2

1

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Peripheral DMA Descriptor Ready Register

Reactivate Descriptor 
Fetch

Read/write

Reset = 0x0000

For MMR assign-
ments, see 

Table 9-9

.

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

e-con Systems ACC-CX3RDK-CU5640 Getting Started Manual preview
ACC-CX3RDK-CU5640
Brand: e-con Systems Pages: 9
Genie WONVR216P5 Quick Start Manual preview
WONVR216P5
Brand: Genie Pages: 15
Dolphin IBP-G4x16-2 User Manual preview
IBP-G4x16-2
Brand: Dolphin Pages: 9
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Brand: Ubiquiti Pages: 13
TP-Link VIGI NVR1004H-4P Quick Installation Manual preview
VIGI NVR1004H-4P
Brand: TP-Link Pages: 2
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Brand: PaloAlto Networks Pages: 28
Renesas R8C/2F Quick Start Manual preview
R8C/2F
Brand: Renesas Pages: 6
FabiaTech FB2701 User Manual preview
FB2701
Brand: FabiaTech Pages: 86
Allied Telesis AT-TN109-A Specifications preview
AT-TN109-A
Brand: Allied Telesis Pages: 2
INGENIA Everest CORE Product Manual preview
Everest CORE
Brand: INGENIA Pages: 58
Rohm BD7682FJ-EVK-301 Quick Start Manual preview
BD7682FJ-EVK-301
Brand: Rohm Pages: 6
U-Media WST-375L User Manual preview
WST-375L
Brand: U-Media Pages: 42
LG Innotek ETWCFLBC01 User Manual preview
ETWCFLBC01
Brand: LG Innotek Pages: 14
ASROCK iBOX-155 Quick Installation Manual preview
iBOX-155
Brand: ASROCK Pages: 2
Crestron Zum ZUMMESH-NETBRIDGE Quick Start preview
Zum ZUMMESH-NETBRIDGE
Brand: Crestron Pages: 2
Icom CT-M500 User Manual preview
CT-M500
Brand: Icom Pages: 7

Brands by name

Popular brands

Load more brands