manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

ADSP-BF535 Blackfin Processor Hardware Reference

9-11 

 

Direct Memory Access

The DMA transfer sequence is completed when the count value in the 
DMA Transfer Count register has decremented to zero. Upon completion 
of the transfer sequence, the DMA channel: 

• Clears  the 

DBO

 bit of the DMA Configuration register, returning 

ownership to the processor

• Copies the contents of the DMA Configuration register to the 

DMA Configuration Word of the current descriptor block. 

• This write-back includes the final status of the transfer sequence. 

• Generates an interrupt if interrupts are enabled (see the appropriate 

peripheral chapter for more information) 

• Fetches the Configuration Word of the next descriptor block 

• The process continues.

The flow diagram in 

Figure 9-2

 and 

Figure 9-3

 shows how the DMA 

channel performs two consecutive DMA transfers using descriptor blocks. 
(The structure of the descriptor blocks is shown in 

Figure 9-1 on 

page 9-4

.) 

Figure 9-4 on page 9-14

 illustrates the time segments from the 

flow diagram (Time T1 through Time T5).

In 

Figure 9-4

, the actions in T1 and T2 are the same as those in T3 and 

T4 except for the name of the descriptor block. 

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

Paradyne 3163 Quick Reference preview
3163
Brand: Paradyne Pages: 16
3Com 3C3FE574BT Quick Start Manual preview
3C3FE574BT
Brand: 3Com Pages: 8
Palo Alto Network M-200 Reference Manual preview
M-200
Brand: Palo Alto Network Pages: 56
T&D RTR-50 User Manual preview
RTR-50
Brand: T&D Pages: 122
Acqiris SA217P Startup Manual preview
SA217P
Brand: Acqiris Pages: 22
Falcon 4G COMBO User Manual preview
4G COMBO
Brand: Falcon Pages: 24
LSI MegaRAID SATA 300-4XLP Quick Installation Manual preview
MegaRAID SATA 300-4XLP
Brand: LSI Pages: 3
Daedalon EC-33 Instruction Manual preview
EC-33
Brand: Daedalon Pages: 6
ekwb EK-Loop Modulus Series User Manual preview
EK-Loop Modulus Series
Brand: ekwb Pages: 7
JYTEK PCIe/PXIe-6301 Series User Manual preview
PCIe/PXIe-6301 Series
Brand: JYTEK Pages: 46
Atmel STK501 Specification Sheet preview
STK501
Brand: Atmel Pages: 2
Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 Manual preview
LEDWALL Optimizer HQ P2
Brand: Gundermann VIDEOWALL Pages: 12
PairGain T1L2PY0AA Manual preview
T1L2PY0AA
Brand: PairGain Pages: 80
Keil RTX51 Manual preview
RTX51
Brand: Keil Pages: 68
H3C SecPath F1070 Manual preview
SecPath F1070
Brand: H3C Pages: 68
Microscan MS-96 Vial Reader User Manual preview
MS-96 Vial Reader
Brand: Microscan Pages: 67
Lanner NCA-6520 User Manual preview
NCA-6520
Brand: Lanner Pages: 141
Vista VIPER H4 User Manual preview
VIPER H4
Brand: Vista Pages: 93

Brands by name

Popular brands

Load more brands