manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

ADSP-BF535 Blackfin Processor Hardware Reference

12-21 

 

UART Port Controller

When autobuffering is enabled, Data Size Bit 0 and Data Size Bit 1 are 
used to determine the size of a DMA transfer. 

Table 12-15

 defines the 

allowed DMA transfer sizes.

Note the receive DMA always writes to memory, so the Direction bit 
should always be set.

If the Interrupt on Error bit is set, a UARTx RX interrupt is issued when 
either an overflow error, a parity error, or a framing error has been 
detected. The RX interrupt service routine should evaluate bit 1 of the 

UARTx_IRQSTAT_RX

 register in order to determine whether it was requested 

by a line error condition rather than by the DMA completion. If this bit is 
set, the service routine should read the 

UARTx_LSR

 register to determine the 

error condition.

Reading 

UARTx_LSR

 also clears the UART’s interrupt request. Since 

the error request has also been latched in the DMA engine, the 
error handler must also write a 1 to bit 1 of the 

UARTx_IRQSTAT_RX

 

afterward.

Table 12-14. UARTx Receive DMA Configuration Register MMR 
Assignments

Register Name

Memory-Mapped Address

UART0_CONFIG_RX

0xFFC0 1A02

UART1_CONFIG_RX

0xFFC0 1E02

Table 12-15. DMA Transfer Sizes

Data Size Bit 1

Data Size Bit 0

Transfer Size

0

0

16-bit half word

0

1

32-bit word

1

0

Reserved

1

1

8-bit byte

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

B2 ABB2050 Instruction Manual preview
ABB2050
Brand: B2 Pages: 52
Farallon NetLINE USB User Manual preview
NetLINE USB
Brand: Farallon Pages: 26
Observint N16 Quick Setup Manual preview
N16
Brand: Observint Pages: 11
Compaq Proliant 800 Setup And Installation Manual preview
Proliant 800
Brand: Compaq Pages: 112
Mylex eXtremeRAID 1100 Installation Manual preview
eXtremeRAID 1100
Brand: Mylex Pages: 74
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
TRENDnet TEW-641PC Quick Installation Manual preview
TEW-641PC
Brand: TRENDnet Pages: 12
Radio Shack Bluespoon 17-1000 Quick Start Manual preview
Bluespoon 17-1000
Brand: Radio Shack Pages: 1
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Brand: BIIZZY Pages: 2
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
Watchguard Firebox T20 Hardware Manual preview
Firebox T20
Brand: Watchguard Pages: 21
National Instruments PCI-6601 User Manual preview
PCI-6601
Brand: National Instruments Pages: 52
Multiplex MULTIflight Stick Operating Instructions Manual preview
MULTIflight Stick
Brand: Multiplex Pages: 10

Brands by name

Popular brands

Load more brands