manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

SPI Registers

10-14

ADSP-BF535 Blackfin Processor Hardware Reference

 

Multiple Slave SPI Systems

The 

FLSx

 bits in 

SPIx_FLG

 are used in a multiple slave SPI environment. 

For example, if there are eight SPI devices in the system including an 
ADSP-BF535 processor master, the master ADSP-BF535 processor can 
support the SPI mode transactions across the other seven devices. This 
configuration requires only one master ADSP-BF535 processor in this 
multislave environment. For example, assume that SPI0 is the master. The 
seven flag pins (

PF2

, 

PF4

, 

PF6

, 

PF8

, 

PF10

, 

PF12

, and 

PF14

) on the 

ADSP-BF535 processor master can be connected to each of the slave SPI 
device’s 

SPISS

 pins. In this configuration, the 

FLSx

 bits in 

SPIx_FLG

 can be 

used in three cases.

In cases 1 and 2, the ADSP-BF535 processor is the master and the seven 
microcontrollers/peripherals with SPI interfaces are slaves. The 
ADSP-BF535 processor can:

• Transmit to all seven SPI devices at the same time in a broadcast 

mode. Here, all 

FLSx

 bits are set. 

• Receive and transmit from one SPI device by enabling only one 

slave SPI device at a time. 

In case 3, all eight devices connected via SPI ports can be ADSP-BF535 
processors.

• If all the slaves are also ADSP-BF535 processors, then the requestor 

can receive data from only one ADSP-BF535 processor (enabled by 
clearing the 

EMISO

 bit in the six other slave processors) at a time 

and transmit broadcast data to all seven at the same time. This 

EMISO

 feature may be available in some other microcontrollers. 

Therefore, it is possible to use the 

EMISO

 feature with any other SPI 

device that includes this functionality.

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

Samsung AllShare Cast Dongle Quick Start Manual preview
AllShare Cast Dongle
Brand: Samsung Pages: 2
D-Link DSL-2750U Setup preview
DSL-2750U
Brand: D-Link Pages: 14
2N OfficeRoute Quick Manual preview
OfficeRoute
Brand: 2N Pages: 11
2N stargate How To Set preview
stargate
Brand: 2N Pages: 5
2N Telekomunikace EasyGate IP Brief Manual preview
EasyGate IP
Brand: 2N Telekomunikace Pages: 24
Garland P1GCCAS Installation Manual preview
P1GCCAS
Brand: Garland Pages: 4
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
Paradyne MCC Installation Instructions Manual preview
MCC
Brand: Paradyne Pages: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Brand: Paradyne Pages: 19
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Brand: Paradyne Pages: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Brand: Paradyne Pages: 141
Patton electronics NetLink 2960 RAS Datasheet preview
NetLink 2960 RAS
Brand: Patton electronics Pages: 2
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
VMIC VMICPCI-7755 Product Manual preview
VMICPCI-7755
Brand: VMIC Pages: 126
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
Blackmagicdesign Teranex 2D Processor Installation And Operation Manual preview
Teranex 2D Processor
Brand: Blackmagicdesign Pages: 969
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
ekwb EK-FC285 GTX Classified Installation And Mounting Manual preview
EK-FC285 GTX Classified
Brand: ekwb Pages: 2

Brands by name

Popular brands

Load more brands