manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

ADSP-BF535 Blackfin Processor Hardware Reference

6-57 

 

Memory

The MMU is implemented as two 16-entry Content Addressable Memory 
(CAM). Each entry is referred to as a Cacheability Protection Lookaside 
Buffer (CPLB) descriptor. When enabled, every valid entry in the MMU 
is examined on any fetch, load, or store operation to determine whether 
there is a match between the address being requested and the page 
described by the CPLB entry. If a match occurs, the cacheability and pro-
tection attributes contained in the descriptor are used for the memory 
transaction with no additional cycles added to the execution of the 
instruction.

Because the Level 1 memories are separated into instruction and data 
memories, the CPLB entries are also divided between instruction and data 
CPLBs. Sixteen CPLB entries are used for instruction fetch requests; these 
are called 

ICPLBs

. Another sixteen CPLB entries are used for data transac-

tions; these are called 

DCPLBs

. The ICPLBs and DCPLBs are enabled by 

setting the appropriate bits in the Instruction Memory Control 
(

IMEM_CONTROL

) and Data Memory Control (

DMEM_CONTROL

) registers, 

respectively. These registers are shown in 

Figure 6-4 on page 6-14

 and 

Figure 6-3 on page 6-13

, respectively.

Each CPLB entry consists of a pair of 32-bit values. For instruction 
fetches:

•

ICPLB_ADDR[n]

 defines the start address of the page described by 

the CPLB descriptor.

•

ICPLB_DATA[n]

 defines the properties of the page described by the 

CPLB descriptor.

For data operations:

•

DCPLB_ADDR[m]

 defines the start address of the page described by 

the CPLB descriptor.

•

DCPLB_DATA[m]

 defines the properties of the page described by the 

CPLB descriptor.

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Brand: Magma Pages: 2
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Brand: SAF Pages: 30
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
Campbell NL115 User Manual preview
NL115
Brand: Campbell Pages: 38
Barco Encore VPx Installation Manual preview
Encore VPx
Brand: Barco Pages: 30
ZALMAN CNPS12X User Manual preview
CNPS12X
Brand: ZALMAN Pages: 11
Giacomini KPM36Y002 Manual preview
KPM36Y002
Brand: Giacomini Pages: 2
IFM Electronic OVP800 Operating Instructions Manual preview
OVP800
Brand: IFM Electronic Pages: 14
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Brand: Belden Pages: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Brand: OWC Pages: 2
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
TRENDnet TEW-641PC Quick Installation Manual preview
TEW-641PC
Brand: TRENDnet Pages: 12
Radio Shack Bluespoon 17-1000 Quick Start Manual preview
Bluespoon 17-1000
Brand: Radio Shack Pages: 1
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Brand: Promise Technology Pages: 26
Ebyte ECAN-W01 User Manual preview
ECAN-W01
Brand: Ebyte Pages: 23
Renesas R0E424270CFLE0 User Manual preview
R0E424270CFLE0
Brand: Renesas Pages: 4

Brands by name

Popular brands

Load more brands