manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

Reset Behavior and Control

13-16

ADSP-BF535 Blackfin Processor Hardware Reference

 

The PCI core does not generate IDSEL lines for the bus connected to it. 
For accomplishing configuration accesses, the 

PCI_CBAP

 address register 

and the accompanying Configuration Data port are used. The 

PCI_CBAP

 

register contents are placed directly on the address bus during the address 
phase, to allow for maximum flexibility. The system designer must decide 
how to implement the IDSEL lines. This can be done with the upper 
address bits, with external logic, or by other means, and the addresses in 
the 

PCI_CBAP

 must be formatted according to the system design 

requirements.

Reset Behavior and Control

The PCI interface is a bridge between the PCI and the ADSP-BF535 pro-
cessor systems, so it must gracefully handle a reset from either system in 
both host and device modes. The PCI reset signal (

PCI_RST

) comes into 

the ADSP-BF535 processor and resets some registers in the PCI clock 
domain. PCI registers that are not affected by a PCI reset are 

PCI_CFG_DIC

, 

PCI_CFG_VIC

, 

PCI_CFG_STAT

, 

PCI_CFG_CMD

, 

PCI_CFG_MLT

, 

PCI_CFG_CLS

, 

PCI_CFG_MBAR

, and 

PCI_CFG_IBAR

. It signals all state machines interfacing 

the PCI with the internal buses to reset to IDLE. This enables the PCI 
module to completely recover from a 

PCI_RST

, even if it was asserted dur-

ing a transaction to or from the ADSP-BF535 processor. The assertion of 

PCI_RST

 sets the PCI Reset bit of the 

PCI_STAT

 register, and generates an 

interrupt to the core if masked to do so in the 

PCI_ICTL

 register. This 

enables the core to recognize what has happened, especially in the case of 
the reset being asserted during a transaction. A system reset running to the 
PCI module within the ADSP-BF535 processor resets all logic in the PCI 
module, including the registers and state machines in the PCI core. This 
method enables PCI core logic to be reset during the reset of either sys-
tem. It also allows the surrounding logic to return to a known state but 
register the 

PCI_RST

 and only completely reset during an ADSP-BF535 

processor reset.

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

ebm-papst 4112 N/2HU Operating Manual preview
4112 N/2HU
Brand: ebm-papst Pages: 6
ebm-papst 4314 N/2HHPU Operating Manual preview
4314 N/2HHPU
Brand: ebm-papst Pages: 6
ebm-papst 8312 L Operating Manual preview
8312 L
Brand: ebm-papst Pages: 5
Moxa Technologies UC-8100 Series Hardware User Manual preview
UC-8100 Series
Brand: Moxa Technologies Pages: 19
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
IBA ibaFOB-4i-X Manual preview
ibaFOB-4i-X
Brand: IBA Pages: 33
Nortel BayStack 660 Use Manual preview
BayStack 660
Brand: Nortel Pages: 163
Baracoda Scan Dongle User Manual preview
Scan Dongle
Brand: Baracoda Pages: 16
AXIOMTEK UST510-52B-FL Series User Manual preview
UST510-52B-FL Series
Brand: AXIOMTEK Pages: 77
McIntosh MX160 Owner'S Manual preview
MX160
Brand: McIntosh Pages: 44
DIGITAL-LOGIC MICROSPACE MSEBX800 User Manual preview
MICROSPACE MSEBX800
Brand: DIGITAL-LOGIC Pages: 53
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
Cabletron Systems TRXMIM-24A User Manual preview
TRXMIM-24A
Brand: Cabletron Systems Pages: 56
Allied Telesis AT-TN109-A Specifications preview
AT-TN109-A
Brand: Allied Telesis Pages: 2
CAMBRIONIX OEM-U8S User Manual preview
OEM-U8S
Brand: CAMBRIONIX Pages: 43
WAVESYS WSIL-1204-GT2-SFP2 Hardware User Manual preview
WSIL-1204-GT2-SFP2
Brand: WAVESYS Pages: 21
Fujitsu F2MC-16FR User Manual preview
F2MC-16FR
Brand: Fujitsu Pages: 14
Cisco Aironet 1200 Series Hardware Installation Manual preview
Aironet 1200 Series
Brand: Cisco Pages: 138

Brands by name

Popular brands

Load more brands