Avaya DEFINITY Server CSI Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 97

Install DS1 CPE Loopback Jack (T1 Only)

Issue 5 October 2002

97

555-233-119

Loopback Jack Installation

Configurations Using a Smart Jack

The preferred location of the loopback jack is at the interface to the Smart Jack.
This provides maximum coverage of CPE wiring when remote tests are run using
the loopback jack. If the Smart Jack is not accessible, install the loopback jack at
the extended demarcation point.

1. If there is no extended demarcation point, install the loopback jack directly

at the network interface point as shown in

Figure 9 on page 103

.

2. If there is an extended demarcation point and the Smart Jack is not

accessible, install the loopback jack as shown in

Figure 10 on page 104

.

3. If there is an extended demarcation point, but the Smart Jack is accessible,

install the loopback jack as shown in

Figure 11 on page 105

.

Configurations Without a Smart Jack

1. Install the loopback jack at the point where the cabling from the ICSU plugs

into the “dumb” block. If there is more than one “dumb” block, choose the
one that is closest to the Interface Termination feed or the fiber MUX. This
provides maximum coverage for loopback jack tests. See

Figure 12 on

page 106

and

Figure 13 on page 107

.

Installation

1. To install the loopback jack, simply disconnect the RJ-48 (8-wide)

connector (typically an H600-383 cable) at the appropriate interface point
and connect the loopback jack in series with the DS1 span. See

Figure 9

on page 103

through

Figure 13 on page 107

.

2. Plug the H600-383 cable from the ICSU into the female connector on the

loopback jack.

3. Plug the male connector on the loopback jack cable into the network

interface point.

NOTE:

Do not remove the loopback jack after installation. This is not a test
tool and should always be available to remotely test a DS1 span.

«
...
95
96
97
98
99
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов