Avaya DEFINITY Server CSI Скачать руководство пользователя страница 787 | Manualshive

Страница: 787 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 787

AXA12-BD/ADX8D-BD/AXD12-BD (AUDIX Circuit
Packs)

Issue 5 October 2002

787

555-233-119

AXA12-BD/ADX8D-BD/AXD12-BD
(AUDIX Circuit Packs)

The TN 568 is a EMBEDDED AUDIX circuit pack that occupies 2 slots on a port
carrier. The tests below apply only to switch-side maintenance, which tests circuit
pack components related to the TDM bus interface. The AUDIX system has an
extensive maintenance strategy of its own that is described in EMBEDDED
AUDIX System Maintenance, 585-300-110.

AXA12-BD:

On G3r V7 systems, TN568 EMBEDDED AUDIX circuit packs (sometimes called
Embedded AUDIX) operating in control-link mode appear to the system as TN746
Analog Line circuit packs with vintage greater than 50. For circuit-pack-level
problems, see XXX-BD. The maintenance strategy for ports on the TN568
operating in control-link mode is described in ADXCL-PT.

ADX8D-BD:

On G3r V7 systems, TN568 EMBEDDED AUDIX circuit packs operating in 8-port
digital mode appear to the system as TN754 Digital Line circuit packs with vintage
greater than 50. For circuit-pack-level problems, see XXX-BD. The maintenance
strategy for ports on the TN568 operating in 8-port digital mode is described in
ADXDP-PT.

ADX12-BD:

The ADX12-BD maintenance object represents a TN568 EMBEDDED AUDIX
circuit pack operating in 12-port digital (DP) mode. On G3r V7 systems, TN568
EMBEDDED AUDIX circuit packs operating in 12-port digital mode appear to the
system as TN2181 Digital Line circuit packs with vintage greater than 50. For
circuit-pack-level problems, see XXX-BD. Port-level problems are covered by
ADX12D-PT.

MO Name (in Alarm Log)

Alarm Level

Initial Command to Run

Full Name of MO

AXA12-BD

MINOR

test board UUCSS

1

sh

1.

UU is the universal cabinet number. C is the carrier designation (A, B, C, D, or E). SS is the number
of the slot in which the circuit pack resides)(01 to 21).

AUDIX Circuit Pack

AXA12-BD

WARNING

test board UUCSS sh

AUDIX Circuit Pack

ADX8D-BD

MINOR

test board UUCSS sh

AUDIX Circuit Pack

ADX8D-BD

WARNING

test board UUCSS sh

AUDIX Circuit Pack

AXD12-BD

MINOR

test board UUCSS sh

AUDIX Circuit Pack

AXD12-BD

WARNING

test board UUCSS sh

AUDIX Circuit Pack

«
...
785
786
787
788
789
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов