manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 612 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 612

Maintenance Objects

555-233-119

612

Issue 5  October 2002 

ADX8D-BD (AUDIX Circuit Pack)

The ADX8D-BD maintenance object represents a TN566/TN2169 EMBEDDED 
AUDIX circuit pack operating in digital-port (DP) mode. For circuit pack problems, 
see “XXX-BD (Common Port Circuit Pack)”. Port level problems are covered by 
ADX8D-PT.

EMBEDDED AUDIX

 

consists of 2 circuit packs that occupy 4 slots in a port 

cabinet. The tests described in this manual apply only to switch-side maintenance 
which tests circuit pack components related to the TDM bus interface. The AUDIX 
system has an extensive maintenance strategy that is described in EMBEDDED 
AUDIX System Maintenance, 585-300-110.

MO Name (in 

Alarm Log)

Alarm Level

Initial Command To Run

1

1.

Where P is the port network number (1 for PPN); C is the carrier designation (for example, A, B, or 
C); SS is the address of the slot in the carrier where the circuit pack is located (for example, 01, 02, 
etc.).

Full Name of MO

ADX8D-BD

MINOR or WARNINGS

test board PCSS sh

AUDIX Circuit Pack

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов