manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1399 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1399

MMI-BD

Issue 5  October 2002

1399

555-233-119

e. The circuit pack detected an Angel on-board hardware failure. The 

reported aux data values correspond to the following detected errors:
4352 - External RAM error
4253 - Internal RAM error
4355 - ROM Checksum error
4357 - Instruction set error
Reset the circuit pack by using the busyout board PCSS, reset board 
PCSS, and release board PCSS commands. When reset, the circuit pack 
executes a set of tests to detect the presence of any of the above faults. 
The detection of one these errors during initialization causes the circuit 
pack to lock up and appear insane to the system. See the repair 
procedures in note b) for Error Type 1.

f. This MMI circuit pack reported a loss of MMI synchronization. Refer to Test 

(#1123) for repair procedures.

g. A failure of the time slot interchanger has been detected. Reset the circuit 

pack using the busyout board PCSS, reset board PCSS, and release 
board PCSS commands. If the reset passes, then the on-board circuitry is 
healthy. Retire the alarm using the test board PCSS long clear command 
followed by release board PCSS. 

h. The circuit pack is hyperactive; that is, it is flooding the switch with 

messages sent over the control channel. The circuit pack is taken out of 
service when a threshold number of these errors is reported to the switch. 
Clear the alarm using the following commands: busyout board PCSS, 
reset board PCSS, test board PCSS long clear, release board PCSS. If 
the error recurs within 10 minutes, replace the circuit pack.

i. The TSI Cross Talk Test (#6) failed. See the description of this test and 

follow the repair procedures.

j. The TSI Looparound Test (#1108) failed. See the description of this test 

and follow the repair procedures.

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов