Avaya DEFINITY Server CSI Скачать руководство пользователя страница 767 | Manualshive

Страница: 767 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 767

ATM-TRK (Circuit Emulation Service Circuit Pack)

Issue 5 October 2002

767

555-233-119

j. Error Type 1537: LANHO bus timeout. The circuit pack is transmitting too

many bytes on the LAN bus for a single frame. This can be due to:

■

an on-board fault.

■

a faulty data received on one of the circuit pack’s external ports.

If the error occurs 3 times in 10 minutes, the board is isolated from the
Packet Bus and the board is alarmed. To clear the alarm:

1. Restore this circuit pack to the Packet Bus with this command

sequence:

a. busyout board UUCSS

b. reset board UUCSS

c. test board UUCSS long

d. release board UUCSS

2. If the problem persists and there are no PKT-BUS or port alarms,

replace the circuit pack.

k. Error Type 1538: The ATM-TRK circuit pack is hyperactive (sending an

abnormal number of control messages to the processor). Use the following
command sequence for this ATM-TRK circuit pack:

1. busyout board UUCSS

2. reset board UUCSS

3. test board UUCSS long

4. release board UUCSS

5. If this error persists, replace the circuit pack.

l. Error Type 1794: LANHO transmit FIFO overflow. The circuit pack’s

transmit buffers have overflowed.

1. Run test board UUCSS r 5.

m. Error Type 2049: ACL Link Failure (link is down). The ATM Control Link

(ACL) has failed, communication has been interrupted between the SPE
and the ATM-TRK circuit packs on the system, and signaling-group
parameters are not communicated across the packet bus.

1. Check the PKT-BUS (Packet Bus) and SYS-LINK (System Link)

maintenance objects, and follow the repair procedures indicated.

2. Run test board UUCSS against the ATM-TRK circuit pack.

If Then

Test #598 fails

Replace the circuit pack.

If Then

Test 598 fails.

Follow the repair procedures suggested for
that test.

«
...
765
766
767
768
769
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов