Avaya DEFINITY Server CSI Скачать руководство пользователя страница 895 | Manualshive

Страница: 895 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 895

CLSFY-PT (Call Classifier Port)

Issue 5 October 2002

895

555-233-119

101-122

FAIL

Forward or Backward MFC signals were not correctly generated or
detected. This impacts reception of incoming MFC calls.

1. Run the short test sequence with test port PCSSpp sh r 1.

2. If the problem persists, the system is still operating properly but system

capacity will be reduced. In order to restore system performance to
normal, replace the Call Classifier circuit pack containing the defective
CLSFY-PT (Call Classifier Port).

PASS

Tone Detection Verification is successful. The Call Classifier Port
(CLSFY-PT) is able to detect/generate all necessary tones.

Table 152.

TEST #42 Tone Detection Verification Test —

Continued

Error
Code

Test

Result

Description/ Recommendation

Continued on next page

«
...
893
894
895
896
897
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов