manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1837 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1837

UDS1-BD (UDS1 Interface Circuit Pack)

Issue 5  October 2002

1837

555-233-119

2

FAIL

The CLJ-LB test failed because it was not set up properly. The UDS1 interface 
pack could not successfully put the CPE loopback jack into loopback mode.

1. Rerun the test ds1-loop UUCSS cpe-loopback-jack-test-begin 

command.

2. If the test continues to fail, the problem could be with the UDS1-BD board, 

the CPE loopback jack equipment, or somewhere between. Run the test 
ds1-loop UUCSS ds1/csu-loopback-tests command to determine if the 
loopback tests that are closer to the UDS1-BD board are successful. If 
any of these tests fail, follow the maintenance strategy that is associated 
with the test that fails.

3

FAIL

The CPE Loopback Jack Test was not set up properly. The framed 3-in-24 test 
pattern, generated by the UDS1 Interface circuit pack and looped back 
through the CPE Loopback Jack, could not be detected properly by the UDS1 
circuit pack.

1. Retry the test ds1-loop UUCSS cpe-loopback-jack-test-begin 

command.

2. If the CPE Loopback Jack test continues to fail, the problem could be with 

the UDS1-BD board, the CPE Loopback Jack equipment, or somewhere 
in between. Run the test ds1-loop UUCSS ds1/csu-loopback-tests 
command to see if the loopback tests closer to the UDS1-BD board are 
successful. If any of those loopback tests fail, follow the maintenance 
strategy associated with those loopbacks. 

Table 542.

TEST #1212 CPE Loopback Jack Test  — 

Continued

  

Error 
Code

Test 

Result

Description/ Recommendation

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов