Avaya DEFINITY Server CSI Скачать руководство пользователя страница 820 | Manualshive

Страница: 820 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 820

Maintenance Objects

555-233-119

820

Issue 5 October 2002

ISDN-BRI endpoints come in a number of configurations. All endpoints require the
D-channel to convey signaling information to the switch. A voice-only set requires
only one B-channel. A voice and data-capable set requires both B-channels (one
for voice and one for data). Therefore, each TN556 port can support either two
voice-only sets or one voice and data-capable set. Only a single ASAI or adjunct
may be connected to an ISDN-BRI port. Multiple adjuncts per line are not
supported.

Figure 24

illustrates the physical connection (solid line) between an ISDN-BRI

Circuit Pack and a voice or voice/data set. Each physical connection allows for
two B-channels, as stated above, plus one D-channel. Each ISDN-BRI circuit
pack can support up to 12 of these PHYSICAL connections to different voice and
voice/data sets or ASAI and adjuncts.

Figure 24.

ISDN-BRI Set Interactions

This section contains the ISDN-BRI Set, ASAI Adjunct, and Adjunct Maintenance
documentation. Some of the results of maintenance testing of the ISDN-BRI Set
or the ASAI and Adjunct may be affected by the health of the ISDN-BRI circuit
pack and Port. These interactions should be kept in mind when investigating the
cause of ISDN-BRI Set problems.

BRI Line

Circuit Pack

P

O

R

T

D-Channel

B-Channel

B-Channel

PHYSICAL CONNECTION

VOICE

or DATA

SET

Logical Connection

VOICE

or DATA

SET

PBX

Physical Connection

«
...
818
819
820
821
822
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов