manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1739 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1739

TRANS-ID (Translation-ID)

Issue 5  October 2002

1739

555-233-119

Processor replacement procedure screens

Screen 87.

Maintenance-related system parameters (change system-parameters 

maintenance)

7.

Avaya resets the 
translation ID

reset translation-id

Avaya executes the command. 
Distributors or third-party 
vendors must also contact 
Avaya Communications.

NOTE:

The system message, 

Cannot reset 

translation-ID 

without standby 

SPE being 

accessible

, means 

that both processors 
must be sane and 
operational.

8.

Switch to the A-side

reset system 
interchange

Switches SPE control to the 
active, or A-side.

9.

Repeat for High and 
Critical Reliability 
systems

Go back to Steps #3 through 
#8, this time performing the 
steps on the A-side.

Table 516.

Processor circuit pack replacement procedure — 

Continued

  

√

Step

Description

Command

Procedure

Continued on next page

change system-parameters maintenance                    Page   1 of   2   SPE B
                   MAINTENANCE-RELATED SYSTEM PARAMETERS
OPERATIONS SUPPORT PARAMETERS
            Product Identification: 1501137003
        First OSS Telephone Number:                    Abbrev Alarm Report? y
       Second OSS Telephone Number:                    Abbrev Alarm Report? n
  Alarm Origination to OSS Numbers: neither         
        Cleared Alarm Notification? n                 Suspension Threshold: 5 
              Restart Notification? n
           Test Remote Access Port? n
        CPE Alarm Activation Level: none   
     Customer Access to INADS Port? n
       Repeat Dial Interval (mins): 7 
SCHEDULED MAINTENANCE
                  Start Time: 01 : 00                   Stop Time: 01 : 01
           Daily Maintenance: daily              Save Translation: no       
 Control Channel Interchange: daily     System Clocks Interchange: daily    
             SPE Interchange: daily    

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов