manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1374 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1374

Maintenance Objects

1374

Issue 5  October 2002 

MEDPRO (Media Processor MAPD 
Circuit Pack)

The TN802B MedPro circuit board is used to provide voice over IP connectivity. 
The TN802B can run either:

■

R8.1 IP Trunk application — allows the TN802B to emulate a DS1 circuit 
pack. In this mode, the circuit pack is maintained as a standard DS1 board 
with its associated Tie trunk ports. The TN802B operates as an integrated 
Internet Telephony Server (ITS). It communicates with other ITS boxes or 
IP trunk boards.

■

the Media Processor (MedPro) application — allows the TN802B to act as 
a service circuit to terminate generic RTP streams used to carry packetized 
audio over an IP network. As part of the overall H.323 implementation, the 
TN802B or later circuit pack handles the audio streams while the TN799 
C-LAN handles the TCP/IP signaling channels. This maintenance plan 
applies only to a TN802B MedPro running the Media Processor 
application.

The MedPro hardware combines an angel complex, a Windows NT PC and a 
TAP802 DSP card in a 3-slot package. When operating as an IP trunk circuit pack, 
the MedPro emulates a DS1 Tie Trunk circuit pack and blindly responds to DS1 
trunk maintenance requests. Actual maintenance is accomplished via the 
windows NT interface and the ITS software diagnostics. 

The Media Processor application is built upon the existing ITS software, and as 
such is not administered in an Avaya DEFINITY Server as a DS1 trunk, and does 
not emulate a DS1 for maintenance purposes. Use the following Maintenance 
procedures for this application. 

MO Name (in 
Alarm Log)

Alarm 
Level

Initial Command to Run

1

1.

UU is the universal cabinet number (1 for PPN, 2 - 44 for EPNs). C is the carrier designation (A, B,

C, D, or E). SS is the number of the slot in which the circuit pack resides (01 to 21).

Full Name of MO

MEDPRO

MAJOR

test board UUCSS sh

Media Processor MAPD Circuit Pack

MEDPRO

MINOR

test board UUCSS l

Media Processor MAPD Circuit Pack

MEDPRO

WARNING

test board UUCSS sh

Media Processor MAPD Circuit Pack

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов