Avaya DEFINITY Server CSI Скачать руководство пользователя страница 603 | Manualshive

Страница: 603 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 603

upgrade software

Issue 5 October 2002

603

555-233-119

Field descriptions

upgrade software

This command upgrades the software text image, the flash component of the
LMM firmware, the MTP firmware, and the Processor Interface (PI) firmwares. In a
simplex system, the command verifies that a software card-mem is present and
then, if present, proceeds to reprogram the flash memory and perform a level-4
restart. During the restart of the system, the system technician is prompted to
replace the software card-mem with the translation card-mem. Service is provided
upon completion of the system restart. Service down time is 5-12 minutes.

!

WARNING:

Be sure to save translations before this executing this command. It may also
be helpful to read the Feature Interactions for this command before
upgrading the system software.

clan-port

Identifies the port on the CLAN board from which the traceroute
command is issued. This field appears when the board is a CLAN.

Hop

The node number (in sequence). The first node (0) is the address
from which the traceroute command is issued.

Time (ms)

Time from the board to each intermediate destination in
milliseconds. If an error occurs at a node, the entry is repeated with
an error code immediately following the time. Error codes and their
meanings are:

■

!

Unable to reach port

■

!N

Unable to reach network

■

!H

Unable to reach host

■

!P

Failure between endpoints

■

!F

Need fragmentation of data packet

■

!S

Source return failure

■

!X

Packet blocked by filter

IP Address

The 32-bit network address.

Action/Object

Qualifier

Qualifier Description

Logins

Defaults

Feature
Interactions

upgrade
software

none

init
inads
craft

none

See below

«
...
601
602
603
604
605
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов