manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1167 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1167

ETH-PT (Control LAN Ethernet)

Issue 5  October 2002

1167

555-233-119

Error Log Entries and Test to Clear Value

Notes:

a. Error Type 1: Ethernet Local Looparound Test (#1278) failed.

1. Test the port (test port UUCSSpp long).

2. Refer to repair procedures for Test #1278.

b. Error Type 513: Link Integrity Inquiry Test (#1282) failed or CLAN port 

detected loss of Ethernet link integrity. 

Possible causes:

■

Cabling

■

Ethernet transceiver

1. Test the port (test port UUCSSpp long).

2. If the Link Integrity Inquiry Test (#1282) fils, refer to its repair 

procedure.

Table 255.

ETH-PT Error Log Entries

Error Type

Aux 

Data

Associated Test

Alarm 

Level

On/Off 

Board

Test to Clear Value

0

1

1.

Run the Short Test Sequence first. If all tests pass, run the Long Test Sequence. Refer to the
appropriate test description and follow the recommended procedures.

0

Any

Any

Any

test port UUCSSpp s

1 (a)

0

Ethernet Local 
Looparound 
Test (#1278)

MINOR

ON

test port UUCSSpp l r 3

513 (b)

0

Link Integrity Inquiry 
(#1282)

MINOR

OFF

test port UUCSSpp r 2

769 (c)

0

WNG

OFF

1281 (d)

0

1537, 1538 
(e)

Session Status Test 
(#1286)

MINOR

OFF

1793-1920 
(f)

2305-2560 
(g)

2561-2816 
(g)

3329 (h)

TCP/IP Ping Test 
(#1281) 

WNG

OFF

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов