manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1888 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1888

Maintenance Objects

1888

Issue 5  October 2002 

VC-DSPPT

Each Voice Conditioner Circuit Pack (VC-BD) provides two types of resources:

1. Transcoder Resources used for encoding and decoding audio formats

2. Summer Resources used for summing audio from different sources

The eight Voice Conditioner DSP ports are the transcoder resources on the 
VC-BD.

Error Log Entries and Test to Clear Values

MO Name (in 

Alarm Log)

Alarm 

Level

Initial Command to Run

1

1.

Where P is the port network number (1 for PPN); C is the carrier designation (for example, A, B, 
or C); and SS is the address of the slot in the carrier where the circuit pack is located (for example, 
01, 02, etc.), and pp is the address of the port (for example, 01, 02, etc.).

Full Name of MO

VC-DSPPT

MAJOR

test port PCSSpp l r#

Voice Conditioner DSP Port

VC-DSPPT

MINOR

test port PCSSpp l r#

Voice Conditioner DSP Port

VC-DSPPT

WARNING

test port PCSSpp l r#

Voice Conditioner DSP Port

Table 565.

VC-DSPPT Error Log Entries 

Error 

Type

Aux 

Data

Associated Test

Alarm 

Level

On/ Off 

Board

Test to Clear Value

0

1

1.

Run the short test sequence first. If all test pass, run the long test sequence. Refer to the appropriate 
test description and follow the recommended procedures.

0

Any

Any

Any

test port PCSSpp sh r 1

18 (a)

0

busyout port PCSSpp

WNG

OFF

release port PCSSpp

257 (b)

Any

NPE Crosstalk Test (#6)

MIN

ON

test port PCSSpp 1 r 3

513 (c)

Any

VC DSP Port Local TDM 
Loopback Test (#1104)

MIN

ON

test port PCSSpp sh r 3

778 to 
781 (d)

Any

VC Port Reset DSP Test 
(#1106)

MAJ

ON

See note (d)

1025 (e)

WNG

ON

1281 (f)

Any

VC DSP Port DSP 
Loopback Test #(1105)

MIN

ON

test port PCSSpp sh r 3

3840 (g)

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов