manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1793 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1793

UDS1-BD (UDS1 Interface Circuit Pack)

Issue 5  October 2002

1793

555-233-119

1320

FAIL

A CSU Module/Sync Splitter hardware failure, or an ICSU/Sync Splitter serial 
interface audit failure was detected by the UDS1 circuit pack.

1. Replace the CSU module/Sync Splitter, and then run the test again.

2. If the test continues to fail with this error code, replace the UDS1-BD 

circuit pack and run the test again.

3. If the test continues to fail with this error code, then the problem could be 

in the I/O cable between the backplane and the CSU module/Sync 
Splitter.

1321

FAIL

DTE LOS (loss of signal) was detected between the UDS1 board and the 
CSU Module or the Sync Splitter. Either the UDS1 board, the CSU 
Module/Sync Splitter, or the I/O cable between the backplane and the CSU 
module/Sync Splitter (or any combination thereof) has failed. Attempt to 
isolate the problem to one of these areas.

1. Replace the CSU Module/Sync Splitter and run the test again.

2. If the test continues to fail with this error code, then replace the 

UDS1-BD board and run the test again.

3. If the test continues to fail with this error code, the problem could be in 

the I/O cable between the backplane and the CSU module/Sync Splitter.

1322

FAIL

No 5 volts power detected from the UDS1 circuit pack to the CSU Module or 
the Sync Splitter. Problem is probably due to an open fuse on the DS1 board 
or a faulty ICSU/Sync Splitter.

NOTE:

Do not immediately swap DS1 boards as this may blow the fuse on the 
new board.

1. If the test continues to fail with this error code, then replace the CSU 

Module/Sync Splitter and run the test again.

2. Remove the UDS1 from the system and reinsert.

3. Run the test again once the board has finished its reset. 

4. If the test continues to fail with this error code, then replace the 

UDS1-BD board and run the test again.

5. If the test continues to fail with this error code, the problem could be in 

the I/O cable between the backplane and the CSU module/Sync Splitter.

1323

FAIL

A service-affecting CSU Module/Sync Splitter audit failure was detected by 
the UDS1 circuit pack. All administered ports on the UDS1 circuit pack are 
affected and maintenance software will place the ports into the out-of-service 
state.

1. Replace the CSU Module or the Sync Splitter.

Table 530.

TEST #138 Loss of Signal Alarm Inquiry Test  — 

Continued

  

Error 
Code

Test 

Result

Description/ Recommendation

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов