Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1279

Страница: 1279 / 1930

IPMEDPRO (IP Media Processor Circuit Pack)

Issue 5 October 2002

1279

555-233-119

Table 305.

TEST #1406 MP Diagnostic Test

Error
Code

Test
Result

Description/ Recommendation

2012

ABORT

System error:

1. Retry the command at 1-minute intervals a maximum of 5 times.

2100

ABORT

System resources required for this test are not available.

1. Retry the command at 1-minute intervals a maximum of 5 times.

FAIL

The MP Diagnostic test has failed for this TN2302 and the board is in
the OOS state.

1. Issue the busyout board UUCSS command.

2. Issue the reset board UUCSS command.

3. Issue the release board UUCSS command.

4. Issue the test board UUCSS long command.

If the board continues to fail replace the board.

8192
-
8328

FAIL

The FPGA DSP test failed:

1. Issue the busyout board UUCSS command.

2. Issue the reset board UUCSS command.

3. Issue the release board UUCSS command.

4. Issue the test board UUCSS long command.

If the board continues to fail replace the board.

8448
-
8584

FAIL

The TSI FPGS test failed:

1. Issue the busyout board UUCSS command.

2. Issue the reset board UUCSS command.

3. Issue the release board UUCSS command.

4. Issue the test board UUCSS long command.

If the board continues to fail replace the board.

12288
-
12424

FAIL

The TSI DSP test failed:

1. Issue the busyout board UUCSS command.

2. Issue the reset board UUCSS command.

3. Issue the release board UUCSS command.

4. Issue the test board UUCSS long command.

If the board continues to fail replace the board.

Continued on next page

«
...
1277
1278
1279
1280
1281
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1279 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: