Главная
/
Avaya
/
DEFINITY Server CSI
/
Руководство по обслуживанию

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1884 / 1930

Поделиться

Страница: 1884 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1884

Maintenance Objects

1884

Issue 5 October 2002

VC-BD

!

CAUTION:

If the TN788 Voice Conditioner Circuit Pack (VC-BD) is not Vintage 2 or
later, it must be replaced.

The TN788 Voice Conditioner Circuit Pack (VC-BD) is a service circuit pack that
provides conditioning for the audio signals from multimedia equipment based on
the CCITT H.221 standard. The TN788 transcodes, gain adjusts, and bridges the
audio bit streams demultiplexed by the TN787 (MMI) circuit pack and transmits
encoded, exclusive audio conference sums onto the TDM bus so that the MMI
can multiplex the audio, video, and data streams for the H.221 endpoints.

FAIL

VAL circuit pack detected test failure.

If the problem persists, reset the circuit pack (busyout board UUCSS, reset
board UUCSS, and release board UUCSS).

If the problem persists, replace the circuit pack.

PASS

Port circuitry functioning properly.

MO Name (in

Alarm Log)

Alarm

Level

Initial Command to Run

1

1.

Where P is the port network number (1 for PPN); C is the carrier designation (for example, A, B, or
C); and SS is the address of the slot in the carrier where the circuit pack is located (for example, 01,
02, etc.).

Full Name of MO

VC-BD

MAJOR

test board PCSS l r#

Voice Conditioner Circuit Pack

VC-BD

MINOR

test board PCSS l r#

Voice Conditioner Circuit Pack

VC-BD

WARNING

2

2.

Refer to XXX-BD (Common Port Board) Maintenance documentation.

test board PCSS s r#

Voice Conditioner Circuit Pack

Table 563.

TEST #1275 SCOTCH Synchronous Looparound Test —

Continued

Error
Code

Test
Result

Description/ Recommendation

Continued on next page

«
...
1882
1883
1884
1885
1886
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов