manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1387 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1387

MEDPROPT (TN802/TN2302 MED PRO DSP PORT)

Issue 5  October 2002

1387

555-233-119

MEDPROPT (TN802/TN2302 MED 
PRO DSP PORT)

The MEDPROPT maintenance object monitors the health of the MEDPRO digital 
signal processors (DSPs).

The TN802B/TN2302 MAPD (Multi-Application Platform for Avaya DEFINITY 
Server) Media Processor circuit pack provides the audio bearer channels for 
H.323 voice over IP calls. One TN802B/TN2302 circuit pack has one MEDPROPT 
media processing resource. Based on system administration of audio codecs, a 
MEDPROPT can handle either 31 or 22 simultaneous channels of H.323 audio 
processing. If the ip-parameters form specifies only G.711 mu-law or G.711 a-law 
as the audio codecs, the MEDPROPT can service 31 channels. If any other codec 
type (G.723-5.3K, G.723-6.3K, or G.729) is administered, the MEDPROPT can 
only service 22 channels.

The MEDPROPT is physically made up of 11 individual DSPs, but is treated 
logically as one port. If individual DSPs on the TN802B/TN2302 MAPD fail, the 
MEDPROPT remains in-service at lower capacity.

The MEDPROPT is a shared service circuit. It is shared between H.323 trunk 
channels and H.323 stations. An idle channel is allocated to an H.323 
trunk/station on a call-by-call basis.

Error Log Entries and Test to Clear Values

MO Name (in 
Alarm Log)

Alarm Level

Initial Command to Run

Full Name of MO

MEDPROPT

MINOR/WARNING

test port UUCSS or PCSS 
[short/long] [repeat#] | 
[clear]

TN802/TN2302 MEDPRO 
DSP PORT

Table 358.

MEDPROPT Error Log Entries 

Error 

Type

Aux 

Data

Associated Test

Alarm 

Level

On/Off 

Board

Test to Clear Value

0

1

0

Any

Any

Any

test board UUCCSS

1(a)

ANY

DSP Capacity Test 
(#1382)

ON

test board UUCCSS l r5

18(b)

0

busyout port 
UUCSS

WARNING

OFF

release port UUCCSS

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов