Avaya DEFINITY Server CSI Скачать руководство пользователя страница 769 | Manualshive

Страница: 769 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 769

ATM-TRK (Circuit Emulation Service Circuit Pack)

Issue 5 October 2002

769

555-233-119

q. Error Type 3330: LANHO critical error. The circuit pack reports that the

on-board LANHO chip is insane (possibly due to a problem in Packet Bus
arbitration, in the transmission line frame, or in the circuit pack itself). The
circuit pack cannot talk to the Packet Bus.

1. Check for PKT-BUS alarms.

r. Error Type 3585: Major board alarm; failure of critical components

involved in the operation of the circuit pack. The circuit pack has failed, and
the switch can no longer recognize it.

If

Then

There is a
packet-bus alarm.

There is probably a packet-bus problem,
particularly if other circuit packs on the packet bus
report the same error. See the PKT-BUS (Packet
Bus) maintenance object and the packet-bus
fault-isolation and recovery sections of the
maintenance manual for repair procedures.

There are no
packet-bus
alarms.

Run the following command sequence:

busyout board UUCSS

reset board UUCSS

test board UUCSS long

release board UUCSS

The problem
persists.

Replace the ATM-TRK circuit pack.

Aux
Data

Description

1

ATM framer chip failure

2

NCE failed

4

TDM PLD failed

5

All DSPs on the circuit pack have failed

6

Receive Network Processor (RNP) failed

7

Transmit Network Processor (TNP) failed

8

MEMORY read/write failure

9

DUART failure

«
...
767
768
769
770
771
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов