manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1188 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1188

555-233-119

1188

Issue 5  October 2002 

Hardware Error Log Entries and Test to Clear 
Values

NOTE:

The loss of -48 volt power will prevent detection of an external device alarm. 
AC-POWER and DC-POWER alarms could indicate the loss of the external 
device alarm -48 volt power source. ALARM-PT alarms may also indicate a 
loss of power. When analog line ports are administered as analog line 
external device alarms loss of -48 volts will prevent detection of an external 
device alarm.

System Technician-Demanded Tests: Descriptions 
and Error Codes

Always investigate tests in the order presented in the table below when inspecting 
errors in the system. By clearing error codes associated with the External Device 
Alarm Test, you may also clear errors generated from other tests in the testing 
sequence.

External Device Alarm Test (#120)

The External Device Alarm Test requests the state of the External Device Alarm 
from a Maintenance circuit pack and reports the results. The test has no effect on 
the external device itself.

Table 266.

EXT-DEV ADMIN? Error Log Entries 

Error 

Type

Aux 

Data

Associated Test

Alarm 

Level

On/Off 

Board

Test to Clear Value

0

0

Any

Any

Any

test eda-external-device-alrm 
physical location r 2 or 6

1 or 5

Any

External Device 
Alarm Test (#120)

Any

OFF

test eda-external-device-alrm 
physical location r 2 or 6

Order of Investigation

Short Test 

Sequence

Long Test 
Sequence

D/ND

1

1.

D = Destructive; ND = Nondestructive

External Device Alarm Test (MAJOR port) (#120)

X

X

ND

External Device Alarm Test (MINOR port) (#120)

X

X

ND

External Device Alarm Test (WARNING port) (#120)

X

X

ND

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов