manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1753 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1753

UDS1-BD (UDS1 Interface Circuit Pack)

Issue 5  October 2002

1753

555-233-119

UDS1-BD (UDS1 Interface Circuit 
Pack)

2Mbit Japan trunk (TN2242)

The TN2242 2Mbit, 30-port trunk circuit pack supports Japanese TTC private 
networking environments. This circuit pack interfaces only with network 
equipment or other circuit packs of the same model and is incompatible with all 
other digital trunk circuit packs. 

The maintenance strategy for the TN2242 is similar to that of the TN464F or later 
suffix DS1 interface circuit pack. The TN2242 circuit pack is functionally the same 
as the TN464F (without ICSU) with the following exceptions:

■

The Blue Alarm Inquiry Test (#139) always passes for the TN2242

■

The test ds1-loop command is not executed for the TN2242

■

When reset board is run on a TN2242, a different initialization message is 
sent for the local looparound test (Test #135) is executed 

■

Since an Integrated Channel Service Unit (ICSU) is not supported on this 
circuit pack, tests associated with an ICSU are not executed, 

■

Tests associated with new functionality available with the video-enabled 
TN464F are not executed for the TN2242

■

Cyclical Redundancy Check (CRC) is not defined for this circuit pack

■

The D-Channel can be user-assigned to any port 1 - 30, when the signaling 
mode is ISDN-PRI

■

Wideband is not supported

■

Stations (OPS) are not supported

The TN2242 circuit pack also supports specialized versions of CAS (Channel 
Associated Signaling) and ISDN-PRI signaling that pertain to the TTC private 
networking environment in Japan.

MO Name (in 

Alarm Log)

Alarm Level

Initial Command to Run

1

1.

UU is the universal cabinet number (1 for PPN). C is the carrier designation (A, B, C, D, or E). SS
is the number of the slot in which the circuit pack resides (01 to 21).

Full Name of MO

UDS1-BD

MAJOR

test board UUCSS sh

UDS1 Interface Circuit Pack

UDS1-BD

MINOR

test board UUCSS l

UDS1 Interface Circuit Pack

UDS1-BD

WARNING

test board UUCSS sh

UDS1 Interface Circuit Pack

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов