manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1288 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1288

555-233-119

1288

Issue 5  October 2002 

Figure 33.

ISDN-PRI Signaling Link Port Interactions (24 Channel - 

TN767/464C)

For 32-channel interfaces, ports 1-15 and 17-31 on the circuit pack are used as 
B-channels. The 16th port may be used as a B-channel or as a D-channel 
depending on the type of Signaling Group used (see 

Figure 34

).

Figure Notes:

1. B- and D-channel messages are 

routed over the TDM Bus. For 
additional reliability, a duplex 
D-channel can be administered for 
a signaling group and located on a 
different TN464C (or higher) circuit 
pack.

2. TN767B (or higher) or TN464C (or 

higher)

Processor

(TN798)

Slot 1

DS1

Interface

circuit pack

TN767

T

D

M

b
u
s

2

(Port 24)

Pimary

signaling link

Voice or data

(Port 1)

Voice or data

(Port 23)

ISDN -TRK
(B-Channel)

ISDN -TRK
(B-Channel)

ISDN -PLK
(D-Channel)

cydfisd3 RPY 061297

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов