Avaya DEFINITY Server CSI Скачать руководство пользователя страница 323

Страница: 323 / 1930

list mst

Issue 5 October 2002

323

555-233-119

R1:

NOTE:

The Link ID has no meaning for the link establish request, therefore the Link
ID field will contain 0xff 0x.ff

NOTE:

The cancel byte will only be present if the message was built, but could not
be sent.

R3:

NOTE:

The Link ID has no meaning for the link establish request, therefore the Link
ID field will contain 0xff 0xff 0xff 0x.ff

Message[7,8]

= Link ID

Message[9]

= Downlink encode
0x01 - ASAI Link Events
0x02 - TEI Management Message
0x03 - XID Message

Message[10]

= ASAI Link Events:
0x02 - link release request
0x0f - link establish request sent to and received by the lower
level

= TEI Management Message
0x02 - Identity Assigned
0x04 - Identity Check Request
0x06 - Identity Remove

= XID Messages
0x01 - XID Request
0x02 - XID Response

Message[11]

= 0xCA - Cancel Byte

Message[7-10]

= Link ID

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 323 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: