manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 805 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 805

BRI-PORT (ISDN-BRI Port), ABRI-PORT (ASAI 
ISDN-BRI Port)

Issue 5  October 2002

805

555-233-119

BRI Port Local LAN Loop Around Test (#618)

This test is destructive.

This test, which verifies the connectivity of a BRI port across the LAN Bus, 
executes only if the port is out-of-service. The test aborts if calls associated with 
the port are in-progress. Failures of this test indicate either on-board faults 
associated with the BRI-PORT hardware on the circuit pack or problems with the 
LAN Bus, which is used to form connectivity between the switch and the 
BRI-PORT.

The dotted lines in 

Figure 22

 show how a Loop Around Test is performed across 

the Packet Bus for the D-channel.

Figure 22.

Path of the BRI Port Local LAN Loop Around

BRI LINE

CIRCUIT

PACK

PACKET

INTERFACE

PACKET BUS

.
.
.
.
. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

.
.
.
.
.

.
.
. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

. 

.
.
.
.
.
.
. 

. . .

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов