manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1897 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1897

VC-LEV (Voice Conditioner DSP Port Level)

Issue 5  October 2002

1897

555-233-119

The VC circuit pack is maintained by the software similarly to the Tone Detector 
circuit pack. Tone Detector circuit packs may be removed and reinserted in any 
port board slot without administration. The same rule applies to VC circuit packs. 
If a VC circuit pack is removed from service logically (by failing the Archangel 
sanity scan test) or is removed from service physically (by physically removing the 
circuit pack from the carrier), no error/alarm is raised against VC-BD or 
VC-DSPPT maintenance objects. Therefore, if a VC-LEV error/alarm exists, and 
none has been raised against VC-BD or VC-DSPPT maintenance objects, a VC 
circuit pack may have been removed from service causing the VC-LEV 
error/alarm. To resolve a VC-LEV MAJOR alarm, restore the number of VC ports 
available for service to be equal to or more than the calculated port capacity 
(value entered in the 

VCs

 field).

To determine how many VC circuit packs are needed for the MMCH feature:

1. Display the System-Parameters Maintenance form by executing the 

command display system-parameters maintenance.

2. Locate the number listed in the Minimum Maintenance Threshold (

VCs

) 

field. The MMCH feature requires one VC circuit pack for each four ports 
listed in the Minimum Maintenance Threshold (

VCs

) field.

3. Divide the Minimum Maintenance Threshold value by 8 to determine the 

number of VC circuit packs needed. For example, a port capacity of 12 
listed in the Minimum Maintenance Threshold (

VCs

) field would require 2 

VC circuit packs.

4. Use the list configuration command to verify that the number of VC circuit 

packs listed agrees with the required number of VC circuit packs 
(determined in step 3). If the number of VC circuit packs listed in the step 3 
differs from the calculated number, restore the number of VC circuit packs 
to the correct value, in order to resolve the VC-LEV alarm.

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов