manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 939 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 939

CO-TRK (CO Trunk)

Issue 5  October 2002

939

555-233-119

2056

ABORT

An error occurred while trying to obtain results from the TN2402/TN798 
circuit pack.

1. Test the TN2402/TN798 circuit pack.

FAIL

Measured transmission performance was in the unacceptable range as 
administered on the trunk group form. Retrieve a measurement report with 
list testcalls. Make sure that ATMS thresholds are set properly on page 4 
of the trunk group form. Besides the facility, test failures can be caused by 
faulty test lines or switch paths. If the measurements point to a facility 
problem, report the results to the trunk vendor.

8000

FAIL

Measured transmission performance was in the marginal range as 
administered on the trunk group form. This generally means that the trunk is 
usable but has an undesirable amount of noise or loss. If the user does not 
report unacceptable effects, it may not be necessary to take any action. 
Retrieve a measurement report with list testcalls. Make sure that ATMS 
thresholds are set properly on page 4 of the trunk group form.

Table 166.

TEST #844-848 Transmission Test  — 

Continued

  

Error 
Code

Test 

Result

Description/ Recommendation

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов