Avaya DEFINITY Server CSI Скачать руководство пользователя страница 763

Страница: 763 / 1930

ATM-TRK (Circuit Emulation Service Circuit Pack)

Issue 5 October 2002

763

555-233-119

e. Error Type 257: Control Channel Loop Test #52 failed. The circuit pack is

not properly connected with the control channel on the TDM bus.

1. Take the corrective action specified by Test #52.

f. Error Type 513: ATM Crosstalk Test (#1298) failed. The board is writing to

or reading from a TDM time slot that is not allocated to the board, or the
Digital Signal Processor (DSP) selected for this test has malfunctioned.

1. Run test board UUCSS.

2. Take the corrective action specified for Test #1298.

g. Error Type 769, 770: the ATM switch is requesting too many LAPD

retransmissions (off-board ATM cell corruption errors).

1. Check the connections between the fiber cable, the ATM-TRK circuit

pack, and the ATM switch.

2. See PKT-BUS (Packet Bus) for test and corrective procedures.

3. Determine what type of fiber is installed between the ATM-TRK

circuit pack and the ATM switch.

4. Perform ATM loopback tests on the near-end ATM-TRK circuit pack

and on the far-end circuit pack or ATM switch.

Error Type

Aux Data

Description

769

LAPD excessive retransmission requests

770

ATM uncorrectable cell headers - threshold

If Then

There is multimode fiber

Check the length of the fiber. If the
cable is longer than 2 km, it is probably
causing the errors.

There is single-mode fiber or
the length of the multimode
fiber is less than 2 km

The source of the errors can lie in the
ATM facility, the ATM-TRK circuit pack,
or the far-end circuit pack.

If Then

The ATM-TRK circuit pack
fails the loopback test.

The problem is in the ATM-TRK circuit
pack. Replace the circuit pack.

The far-end circuit pack or
ATM switch fails the
loopback test.

The problem is in the far-end circuit pack
or ATM switch. Consult the circuit-pack or
ATM switch documentation for advice.

The equipment at each end
of the ATM span passes
the loopback test

The problem is somewhere in the ATM
span. Lack of bandwidth can be forcing
an intermediate ATM switch to drop cells.

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 763 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: