Главная
/
Avaya
/
DEFINITY Server CSI
/
Руководство по обслуживанию

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1765 / 1930

Поделиться

Страница: 1765 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1765

UDS1-BD (UDS1 Interface Circuit Pack)

Issue 5 October 2002

1765

555-233-119

Figure 59.

TN464E/F DS1 Option switches

Firmware Download Feature

Firmware Download provides an Avaya DEFINITY Server the ability to download
new firmware to one or more UDS1 circuit boards residing in its system. The
download image is copied onto a source (C-LAN) board, using FTP. The image
is then copied to the target boards Flash over the TDM bus. The transfer of the
download image from the source board to the target board is done under switch
software’s control. This process is initiated using the Avaya DEFINITY Server SAT
interface.

If the firmware download fails for this circuit pack, an error is logged, and a alarm
raised (See Error Type 174 for this MO). Also see the FW-DWNLD MO for more
information on trouble shooting firmware download problems.

Ω

Ω

«
...
1763
1764
1765
1766
1767
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов