Avaya DEFINITY Server CSI Скачать руководство пользователя страница 235

Страница: 235 / 1930

display events

Issue 5 October 2002

235

555-233-119

1960

IP GRJ-GRQ: new
LM fail

Gatekeeper request rejected
because of failure to create new
LoginMgr. Possible causes

No available heap memory to
create LoginMgr

Cannot start LoginMgr timer

Clock not set

UID

IP address

1961

IP GRJ-Build GCF
msg

Gatekeeper request rejected:
failure to build a GateKeeper
Confirm (GCF) message (internal
software error).

UID

IP address

1962

IP LRJ-No H323 sig
group

Location Request rejected: no
H.323 signalling group
administered.

UID

IP address

1963

IP LRJ-Build LCF
msg

Location Request rejected: failure
to build a Location Request
Confirm (LCF) message (internal
software error).

UID

IP address

1964

IP DRJ-Null UserID

Disengage Request rejected: the
endpoint ID could not be
converted to a UID.

UID

IP address

1965

IP DRJ-Bld
DCF:Gatewy/MCU

Disengage Request rejected:
failure to build Disengage Request
Confirm (DCF) message for a
gateway or MCU (internal
software error).

UID

IP address

1966

IP DRJ-Endpt not reg

Disengage Request rejected:
endpoint is not registered.

UID

IP address

1967

IP DRJ-Build DCF
msg

Disengage Request rejected:
failure to build a Disengage
Request Confirm (DCF) message
for a non-gateway or MCU user
(internal software error).

UID

IP address

1968

IP BRJ-Null UserID

Bandwidth Request rejected:
invalid endpoint ID was received.

IP address

1969

IP BRJ-Bld
BCF:Gatewy/MCU

Bandwidth Request rejected:
failure to build a Bandwidth
Request Confirm (BCF) message
for a Gateway or MCU (internal
software error).

UID

IP address

Table 18.

Denied IP events —

Continued

Event
Type

Event Description

Explanation

Event
Data 1

Event
Data 2

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 235 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: