manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 712 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 712

Maintenance Objects

555-233-119

712

Issue 5  October 2002 

ANN-PT (Announcement Port)

The TN750 Announcement circuit pack is a service circuit pack that provides an 
integrated means for recording announcements that can be played back on 
demand by call processing as part of a calling feature (that is, announcements on 
hunt group calls). There are 16 Announcement Ports on the Announcement circuit 
pack. Each port can play any integrated announcement, independently of the 
other ports. If there are any errors associated with the circuit pack, refer to 
"ANN-BD (Announcement Circuit Pack)" Maintenance documentation.

The Announcement circuit pack has two processors on it. The first processor, or 
Angel, controls the circuit pack, and communicates with the switch via the control 
channel on the TDM Bus. The second processor, or SP, controls the speech 
memory and announcements. Digital speech is converted from its TDM Bus form 
to an internal storage form (for recording) and vice versa (for playbacks) by the 
140AY device on the circuit pack, which has 16 channels (one for each 
Announcement Port).

General Notes

Here are a few very important general notes that apply to any problem on the 
Announcement circuit pack. The user should read this before attempting to work 
on the TN750 Announcement circuit pack or Announcement Ports, especially if 
the circuit pack needs to be replaced.

1. The TN750/B Announcement circuit pack retains all integrated 

announcements as long as the circuit pack has power. For this reason, 
whenever there is a problem with either the Announcement circuit pack or 
an Announcement Port that may require the circuit pack to be reset, it is 
always better to try to reset the circuit pack with reset board PCSS first 
and, if that does not work, try to reseat it. Announcements are preserved 
through a software reset, but they are lost when the circuit pack is 
reseated.

MO Name (in 

Alarm Log)

Alarm 

Level

Initial Command to Run

1

1.

Where P is the port network number (1 for PPN); C is the carrier designation (for 
example, A, B, or C); and SS is the address of the slot in the carrier where the 
circuit pack is located (for example, 01, 02, etc.).

Full Name of MO

ANN-PT

MINOR

test port PCSSpp l

Announcement Port

ANN-PT

WRN

test port PCSSpp l

Announcement Port

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов