manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1863 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1863

VAL-BD (Voice Announcements over LAN Circuit Pack)

Issue 5  October 2002

1863

555-233-119

g. Error Type 3586 and 3999: Switch removed hyperactive circuit pack that 

reported threshold number of errors. One or more of the following 
symptoms can be present:

■

Circuit pack port tests return NO BOARD.

■

List configuration command shows circuit pack and ports are 
installed properly

1. Busyout (busyout board UUCSS) and release (release board 

UUCSS) the circuit pack.

2. Allow 30 minutes for condition to clear itself.

3. To re-establish circuit pack into service manually, busyout (busyout 

board UUCSS), reset (reset board UUCSS), and release (release 
board UUCSS) the circuit pack.

4. If error recurs within 15 minutes, replace the circuit pack. 

5. If the same error occurs on a different circuit pack, follow normal 

escalation procedures.

h. Error Type 3840: Circuit pack received bad control channel message from 

switch.

Aux Data:

If Error Type 3999:

And traffic 
volume is:

Then:

Does not accompany 
Error Type 3586,

Heavy

Circuit pack is in service, but sent 
at least half hyperactive 
threshold. With heavy traffic, this 
is normal.

Does not accompany 
Error Type 3586,

Light

Circuit pack is in service, but sent 
at least half hyperactive 
threshold. With light traffic, this 
error indicates a problem with the 
circuit pack, its links, or the 
equipment attached to the links.

Accompanies Error 
Type 3586,

Either Light or 
Heavy

Switch removed hyperactive 
circuit pack.

4096

Bad major heading

4097

Bad port number

4098

Bad data

4099

Bad sub-qualifier

4100

State inconsistency

4101

Bad logical link

4102

Bad application identifier

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов