manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1169 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1169

ETH-PT (Control LAN Ethernet)

Issue 5  October 2002

1169

555-233-119

g. Error Type 2305-2816: System software detected a session is down. Aux 

Data indicates the session number. These are log only errors. Error types 
2305-2560 are for session numbers 1-256. Error types 2561-2816 are for 
session numbers 257-512.

h. Error Type 3329: TCP/IP Ping Test failed. 

1. Test port (test port UUCSSpp short).

2. Refer to TCP/IP Ping Test (#1281) repair procedures.

System Technician-Demanded Tests: 
Descriptions and Error Codes

Investigate errors in the order they appear in the table below.

Table 256.

System Technician-Demanded Tests: ETH-PT

Order of Investigation

Short Test 

Sequence

Long Test 
Sequence

D/ND

1

1.

D = Destructive, ND = Non-destructive

Ethernet Local Loop-Around Test (#1278)

X

D

TCP/IP Ping Test (#1281)

X

X

ND

Session Status Test (#1286)

X

X

ND

Link Integrity Inquiry Test (#1282)

X

X

ND

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов