Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1928

Страница: 1928 / 1930

Index

555-233-119

1928

Issue 5 October 2002

safety precautions

Save Announcements screen

Save Translation screen

Second OSS Telephone Number

187

253

security

logins

measurements

passwords

Service Marks

setting

bit rate

126

line impedance

126

signaling leads, DC power

124

simplex mode tests

SPE-down mode

switch processing elements (SPE)

249

switch settings

TN464 circuit pack

126

TN760 tie trunk

124

synchronization

system features

troubleshooting system resources

system reboots

system resets

reasons for

System Tone Test Call

T1 DS1 span

TDM bus

clocks

1416

1667

TDM bus clock (TDM-CLK)

1667

terminal

type

Terminal Alarm Notification

alarms

110

description

110

Terminating Trunk Transmission (TTT)

tests

test license

567

testing

background

demand

maintenance

system technician-demanded

1270

1377

1389

1777

tests

analog tie trunk back-to-back

E&M mode

logins

simplex mode

Terminating Trunk Transmission (TTT)

tests and audits

#11 Digital Line Electronic Power Feed Test

1038

1563

#1201 Digital Terminal Remote Loop Around Test

1033

#1209 Board Loopback Test

1116

#1209 DS1 Board Loopback Test

1116

1823

#1210 CSU Equipment Loopback Test

1119

1120

1826

#1211 CSU Repeater Loopback Test

1123

1124

1830

#1212 CPE Loopback Jack Test

1127

1835

#1213 Far CSU Loopback Test

1132

1840

#1214 One-Way Span Test

1136

1844

#1215 Inject Single Bit Error Test

1139

1847

#1216 End Loopback/Span Test

1141

1850

#122 Cabinet Temperature Query Test [Non-Variable

Speed Fans]

849

#1227 ICSU Status LEDs Test

1144

1853

#13 Voice and Control Channel Local Loop Test

1040

#135 Internal Loop Around Test

1084

1782

#138 Loss of Signal Alarm Inquiry Test

1087

1088

1788

1855

#139 Blue Alarm Inquiry Test

1094

1796

#139 Red Alarm Inquiry Test

1098

#140 Red Alarm Inquiry Test

1097

1799

#140AY Loop Around Test

707

#141 Yellow Alarm Inquiry Test

1101

1102

1804

#142 Major Alarm Inquiry Test

1104

1809

#143 Minor Alarm Inquiry Test

1107

1812

#144 Slip Alarm Inquiry Test

1109

1643

1815

#145 Misframe Alarm Inquiry Test

1112

1818

#146 Translation Update Test

1115

1274

1372

1381

1821

#148 TDM Bus Clock Circuit Status Inquiry Test

1673

#150 TDM Bus Clock PPM Inquiry Test

1675

#151 TDM Bus Clock Parameter Update Test

1676

#16 DIG-LINE Station Lamp Updates Test

1042

1564

#161 Loop Around Test

804

1632

#17 Station (Digital) Audits Test

1044

1566

#205 Channel Administration Memory Array (CAMA)

Test

716

#206 Playback Speech Memory Array (PSMA) Test

718

#208 Angel-Speech Processor (SP) Handshake

Test

703

#209 Announcement Checksum Test

704

#211 Super Frame Match Inquiry Test

710

#212 Clock Match Inquiry Test

711

#222 140AY Channel Sanity Inquiry Test

721

#240 Expansion Interface Local Looparound

754

#242 Expansion Interface Lightwave Transceiver

Looparound

1391

1393

#252 Circuit Pack Restart Test

883

884

#255 Signaling Link State Check Test

733

#256 Service State Audit Test

735

#257 Call State Audit Test

736

#258 ISDN Test Call

737

#270 Clear Error Counters

818

1631

#314 DS1 CO Dial Tone Seizure Test

1054

#314 DS1CO Dial Tone Seizure Test

910

#35 Battery Feed Test

663

#36 Port Audit and Update Test

908

1053

«
...
1926
1927
1928
1929
1930
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1928 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: