Avaya DEFINITY Server CSI Скачать руководство пользователя страница 324

Страница: 324 / 1930

Maintenance Commands

555-233-119

324

Issue 5 October 2002

NOTE:

The cancel byte will only be present if the message was built, but could not
be sent.

0x52 - ASAI maintenance uplink

Message[11]

= Downlink encode
   0x01 - ASAI Link Events
   0x02 - TEI Management Message
   0x03 - XID Message

Message[12]

= ASAI Link Events:
   0x02 - link release request
   0x0f - link establish request sent to and received by
     the lower level

= TEI Management Message
   0x02 - Identity Assigned
   0x04 - Identity Check Request
   0x06 - Identity Remove

= XID Messages
0x01 - XID Request
0x02 - XID Response

Message[13]

= 0xCA - Cancel Byte

Message[1]

= Port Network Number of ASAI port

Message[2]

= Reserved

Message[3]

= Carrier Address of ASAI port

Message[4]

= Port number of ASAI port

Message[5]

= 0

Message[6+]

= standard or abbreviated ASAI message format

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 324 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: