manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1624 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1624

Maintenance Objects

1624

Issue 5  October 2002 

TBRI-PT (TN2185 
ISDN Trunk-Side BRI Port)

This document describes the port maintenance features of the Avaya DEFINITY 
Server ISDN Trunk-side BRI board (TN2185). The circuit pack provides 8 S/T 
ISDN 2B+D ports which interface to either the central office or another PBX.

The TN2185 circuit pack contains eight, 4-wire ports that interface to the network 
at the ISDN S/T reference point over two 64 Kb/s channels (B1 and B2) and over 
a 16Kb/s signaling (D) channel. The B1 and B2 channels can be simultaneously 
circuit switched, or individually packet switched. Only one channel per trunk can 
be packet switched due to Packet Processing Element (PPE) limitations. The D 
channel is either circuit switched or packet switched. Packet switching uses the 
PPE to combine all D channels into a single physical channel, which is then 
routed via the concentration highway to the Network Control Element (NCE) and 
then to the TDM bus. The circuit-switched connections have a Mu-law or A-law 
option for voice and operate as 64Kb/s clear data channels. The packet-switched 
channels support the LAPD protocol and conform with the CCITT Q.920 
Recommendations for D-channel signaling. 

LEDs

The three LEDs on the circuit pack’s faceplate indicate board status. When 
illuminated, the red LED indicates a board failure or a major or minor on-board 
alarm, the green LED indicates that testing is in progress, and the amber LED 
indicates that the board is in use.

MO Name (in 

Alarm Log)

Alarm Level

Initial Command to Run

1

1.

Where P is the port network number (1), C carrier designation (A, B, or C), and SS is the 
carrier slot address where the circuit pack is located (1, 2, and so forth).

Full Name of MO

TBRI-PT

MAJOR

test port PCSS l r#

TBRI-PT

TBRI-PT

MINOR

test port PCSS l r#

TBRI-PT

TBRI-PT

WARNING

test port PCSS s r#

TBRI-PT

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов