Avaya DEFINITY Server CSI Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 81

Troubleshooting Features

Issue 5 October 2002

81

555-233-119

Analog Tie Trunk Back-to-Back Testing

The TN760B circuit pack can be configured for back-to-back testing (also known
as connectivity testing) by making translation and cross-connect changes. This
testing configuration allows for the connection of Tie Trunks back-to-back in the
same switch to verify the operation of Tie Trunk ports. The tests can be performed
in either the E & M or simplex modes.

50

Digital milliwatt

51

440 Hz + 480 Hz

52

Music

53

Transmission test sequence 100

54

Transmission test sequence 102

55

Laboratory test tone 1

56

Laboratory test tone 2

57

Disable echo supervision dial tone

58

7 seconds of answer tone

59

4 seconds of answer tone

60

Restore music (or silence)

61

Warning tone

62

Forced music tone

63

Zip tone (first of 2 sent)

64

Incoming call ID (first of 2 sent)

65

Tone on hold

66

CO dial tone

67

Repetitive confirmation tone

68

Conference/bridging tone

Table 6.

System Tone Identification Numbers —

Continued

Number

Description

Continued on next page

«
...
79
80
81
82
83
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов