manualshive.com logo in svg

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1342 / 1930

Поделиться
Скачать
Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1342

Maintenance Objects

1342

Issue 5  October 2002 

MAPD-BD (MAPD Interface Circuit 
Pack TN802)

The TN802 Multiple Application Platform for Avaya DEFINITY Server (MAPD) 
circuit pack allows sending voice and fax from an Avaya DEFINITY Server 
through the Internet to another Avaya DEFINITY Server that also has this feature, 
or to other PBXs that are equipped with the Internet Telephony Server (ITS-E). 

Throughout this section the term TN802 means the MAPD IP trunk circuit pack. 

Be sure to observe these special considerations for the TN802:

■

Port alarms on the TN802 appear as “TIE-DS1” in the Alarm and Error 
logs. 

■

reset board reboots the MAPD PC CPU

■

busyout board busies out only the emulated ports on the board

■

Switch resets that take the switch out of service for more than 20 seconds 
also cause the MAPD's PC to reboot, which takes several minutes to 
complete.

Switch-demanded tests

Switch-demanded diagnostic tests on the TN802 run when the Internet trunking 
application is running on Windows NT

TM

, located on the circuit pack.

MO Name (in 

Alarm Log)

Alarm 

Level

Initial Command to 

Run

1

1.

UU is the universal cabinet number (1 for PPN, 2 - 44 for EPNs). C is the carrier 
designation (A, B, C, D, or E). SS is the number of the slot in which the circuit pack 
resides (01 to 21).

Full Name of MO

MAPD-BD

MAJOR

test board UUCSS sh

MAPD Interface Circuit Pack

MAPD-BD

MINOR

test board UUCSS l

MAPD Interface Circuit Pack

MAPD-BD

WARNING

test board UUCSS sh

MAPD Interface Circuit Pack

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов