Главная
/
Avaya
/
DEFINITY Server CSI
/
Руководство по обслуживанию

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1215 / 1930

Поделиться

Страница: 1215 / 1930

Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1215

FW-DWNLD (Firmware Download)

Issue 5 October 2002

1215

555-233-119

d. Error Type: 513 — indicates that the schedule has failed. Failure of the

schedule can result from any of the previously mentioned log only errors
(257 - 259), the schedule timer expiring, or the disable firmware
download command. To resolve the error and clear the alarm, use the
command test firmware download. The Aux Data specifies the reason
why the schedule failed. See the table below for more details.

6

TFTP protocol error - One reason for this type of failure could be that
the target board has ami-zcs line coding, and is located in a EPN with
ami-zcs line coding between the source and target board. To have a
successful firmware download you must have a clear channel
between the source and target board. Some examples of the correct
type of line coding for this feature are: b8zs, and hdb3.

7

File transfer timer expired, check board location, translations and
retry.

8

Target failed to reset after transfer, check board location, translations
and retry.

10

Download of target failed, check location, translations, and retry.

13

The target board rejected the download image. Check translations,
verify image file, retry then escalate.

20

Could not open the requested file - Internal firmware error on target
board, retry download if fail then escalate.

21

Problem reading the requested file - Internal firmware error on target
board, retry download if fail then escalate

22

The download file has a bad CRC - Internal firmware error on target
board, retry download if fail then escalate

24

A download is already in progress - Internal firmware error on target
board, retry download if fail then escalate

30

A start download sequence error - Internal firmware error on target
board, retry download if fail then escalate

32

The file name is too long - Internal firmware error on target board, retry
download if fail then escalate

40

FLASH programming failed on firmware - Internal firmware error on
target board, retry download if fail then escalate

Table 274.

Error Type 259 Aux Data

— Continued

Aux
Data

Description of Failure

Continued on next page

«
...
1213
1214
1215
1216
1217
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов