Avaya DEFINITY Server CSI Скачать руководство пользователя страница 1893

Страница: 1893 / 1930

VC-DSPPT

Issue 5 October 2002

1893

555-233-119

VC-DSP Port DSP Loopback Test (#1105)

This test is destructive.

This test verifies the connectivity of a VC-DSPPT across the TDM bus as shown
in

Figure 64

. It aborts if calls associated with the port are in progress. Failure of

this test indicates an on-board fault associated with the port hardware on the
circuit pack.

Figure 64.

VC Circuit pack DSP Port DSP Looparound Test

«
...
1891
1892
1893
1894
1895
...
»

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 1893 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: