Avaya DEFINITY Server CSI Скачать руководство пользователя страница 128

Страница: 128 / 1930

Maintenance for CSI systems

555-233-119

128

Issue 5 October 2002

Table 16

shows the various LEDs on the A500 ATM switch and the meanings of

the different states.

100ms on /
100ms off

Loss of signal on the OC-3 fiber. Either the
TN230X-receive (top) or TN230X-transmit (bottom)
fibers are not working.

N/S

Fast blink

Running DSP diagnostics or downloading code to DSPs
(typical during boot process).

Slow blink

Board insertion has not yet completed.

Steady on

Running maintenance tests. May appear to be blinking if
several short tests are run one after another.

Steady on

Hardware alarm. Does not necessarily take the TN230X
out of service, for example, if one of the 24 DSPs fails
diagnostics.

Table 16. A500 LED Quick Reference

Component

Label

Color

State

Meaning

Switch
Processor
Board

Green

Intermittent
blink

Normal state. Traffic is being sent or received
over the Ethernet LAN link.

Green

Steady on

Normal state. Carrier is received over the
Ethernet LAN link.

DIAG

Green

Off

Normal state.

NBOOT

Green

Off

Normal state.

MGT

Green

Off

Normal state.

RUN

Green

Steady on

Normal state. The switch processor is
running.

PWR

Green

Steady on

Normal state. The switch processor board is
powered up.

VOLT

Yellow

Off

Normal state

TEMP

Yellow

Off

Normal state

FAN

Yellow

Off

Normal state

Continued on next page

Table 15.

TN230X LED reference

—

Continued

LED color

Interpretation

Red

Green

Yellow

Continued on next page

Содержание DEFINITY Server CSI











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server CSI

Отзывы:

Avaya DEFINITY Server CSI, Руководство по обслуживанию, Страница: 128 / 1930

Результаты поиска

Содержание DEFINITY Server CSI

Отзывы: